These blades fit all Andis Model AG, AG2, AGC, AGR and MBG Dog Clippers, plus Oster A-5 and similar models, and Double K Clippers. They also fit all Wahl K2 Professional and SwitchBlade Professional clippers.

Andis Clipper Blades are made of high quality carburized steel which extends edge life.

The cut indicates the uniform length of hair which will be left when you use the designated blade. Higher blade numbers indicate shorter hair length ie: A #4 blade leaves 3/8 inch of hair, and a #40 leaves only 1/100 of an inch. For lengths longer than 5/8", use a blade guard or comb.

Don't forget Lubricating Spray to cool and lubricate your blades.

Use Take Down Quick Dog Clipper Blades for Spaniels, Chows, Old English Sheepdogs, Huskies and many other deep-coated or matted dogs. Extra wide blade takes coat off faster.

• Coarse Clipper Blades cut to a medium-long stubble approximately 3/16" (4.8mm)
• Medium Clipper Blades cut close, smooth. Leaves hair approx. 1/8" (3.2mm)
• Fine Clipper Blades cut close, for extremely difficult cuts. Leaves hair approx 1/16" (1.65mm)

Works with all Oster Turbo A-5 Clippers, Power Pro Dog Clippers, and A-5 Dog Clippers currently offered by Futurepets. ( A-5 clippers older than 2003 cannot use this blade). Also works with 2 Speed or Super 2-Speed Andis Clippers.

Don't forget Kool-Lube to cool and lubricate your blades.

Set of 7 BLADE GUARDS includes:
• 1/16"
• 1/8"
• 1/4"
• 1/2"
• 3/4"
• 1"
• 1-1/4"

Best performance when used with a #40 blade.

Use on Andis, Oster A-5 Models, and Lucky Dog Clippers.

New Cryogen-X with AgION Antimicrobial Dog Clipper Blades
• Built-in AgION® Antimicrobial protection reduces the growth of a broad range of bacteria, mold and mildew
• Up to 30 degrees cooler than Standard Oster Blades
• New technology offers the sharpest, coolest blade possible

The cut indicates the uniform length of hair which will be left when you use the designated blade.

Usually, higher blade numbers indicate shorter length ie: A #3 blade leaves 1/2" of hair, and a #40 leaves only 1/100 of an inch. For lengths longer than 1/2", use a blade guard or comb.

Easy to use - simply attach the guard comb to the base of the dog clipper blade, pull up and secure into position. Leaves a longer uniform length.

Best performance when used with a #40 blade. (purchase below)

Use on Andis, Oster A-5 Models, and Lucky Dog Clippers.

Oster Kool Lube New Formula

Simply spray Kool Lube III through the dog clipper blades occasionally, during the time you are clipping. It is nonflammable and non-conductive and can be sprayed while equipment is running. The results are reduced friction, heat and less blade wear without a heavy residue of oil.

Kool Lube cannot be shipped by air

With little time and no inconvenience, you can sharpen them yourself.

Powered by an efficient electric motor, the rotating diamond pad restores all brands of grooming clipper blades and shears to professional standards.

Handihone Dog Clipper Blade Sharpener Features:
• Self-contained, efficient electric model
• Long-wearing diamond-coated sharpening surface quickly restores the clipper blades cutting surface while removing only a minimal amount of blade material.
• Compact, lightweight design is easy to use and maintain.
• No messy sharpening compound or honing oils are used.
• Incorporates proper curve for A-5 and similar hollow-ground blades.
• Great for traveling to shows or exhibitions.

New ConairPro Ceramic Replacement blades offer the coolest, sharpest technology possible.
• Up to 50% cooler than Standard Titanium or steel Blades
• Stays sharper and stays sharper longer than regular blades - Stays sharp 6 to 8 times longer
  Ceramic blades can be sharpened on a fine diamond wheel. However, it is VERY economical to just replace the cutter when sharpening is needed. At a cost of $3 to sharpen a blade, it will cost $18 to $24 to sharpen a regular blade 6-8 times. You can replace the cutter of a ceramic blade only once in that same time frame for only a fraction of that amount.
• Ceramic (glass edge) give a finer, smoother cut

The cut indicates the uniform length of hair which will be left when you use the designated blade.

Usually, higher blade numbers indicate shorter length ie: A #3 blade leaves 1/2" of hair, and a #40 leaves only 1/100 of an inch. For lengths longer than 1/2", use a blade guard or comb.

Andis Dog Dog Clipper Blade Lubricant Features:
1. Cools
2. Lubricates
3. Prevents Rust
4. Cleans
5. Kills Germs, bacteria, fungi